C1357 Engine Trouble Code

When you check engine light came on code C1357 the reason should be . However your vehicle's manufacturer may have a different definition for the C1357 OBD-II Diagnostic Chassis (C) Trouble Code. So you should chech it on our car models.

C1357 code can be about changing a broken oxygen sensor can lead to a busted catalytic convertor which can cost upwards of $1,300. Taking your vehicle into a service shop will cost you around $300 depending on the vehicle. But, an oxygen sensor is easy to replace on many vehicles and is detailed in the owner's manual PDF or in our website. If you know where this sensor is located, you only have to unclip the old oxygen sensor and replace it with a new sensor. Regardless of how you approach it, you should get this fixed right away.

C1357 Code Meaning :

The oxygen (02) sensors on your car measure the oxygen in the exhaust to determine how rich or lean the ratio of fuel and air are in the cylinders. Optimizing this mixture means better fuel economy and fewer exhaust emissions.

C1357 OBD-II Diagnostic Chassis (C) Trouble Code Description

C1357 engine trouble code is about Crankshaft Position Sensor B Circuit Malfunction. Fuel Rail Pressure Sensor Circuit Malfunction and Turbocharger Boost Sensor A Circuit Low causes most of code C1357.

Reason For C1357 Code

The reason of C1357 OBD-II Engine Trouble Code is Fuel Rail Pressure Sensor Circuit Malfunction.

Your car parts or components should not be replaced with reference to only a C1357 DTC. The vehicle service manual should be consulted for more information on possible causes of the error code, along with required testing.

How To Repair C1357 Code

Before starting let's see C1357 repairing process steps:

• Qualified technicians will begin by using a scan tool to access C1357 code stored in the ECU.
• Technicians will note C1357 code present and any freeze frame data associated with them.
• After all, if you sure the engine trouble is finished, the code will be cleared.

When detecting a faulty oxygen sensor, your car will be working less efficiently, so it will periodically hold a defective idle, abnormal jerking at an accurate throttle, errors with hard starting, thus all of these symptoms will cause a high fuel consumption that induces you into detecting for an engine light to illuminate.

The computer installed in each fuel-injected vehicle has to be aware of two factors before it can solve the proper cold-start air/fuel compound: the engine coolant temperature and the exterior air temperature. Your symptoms are exactly the same to a faulty engine coolant temperature sensor (ECT). The computer is measuring an air/fuel compound that is excessively meager.

Sometimes C1357 code comes with C135700 code.

Diagnosis Of Engine Error OBD Code C1357

It's essential to diagnose this trouble code. Then are some way which a handyperson should follow for diagnosing the problem that started a C1357 trouble code to be stored

The first step is introductory and is about reacquiring all the canons that have been set. For this, the individual scanner will have to be plugged into the individual harborage of your vehicle. Make sure you indurate frame the data. Any canons that were set previous to the C1357 code will have to be sorted first, as they may have been the reason for the law to set in the first place. It's always good to rule that out.

The coming step is to run a introductory examination of all the electrical circuits, connectors, wiring etc for damages similar as becks, erosion, fraudulent legs etc. All of these will have to be repaired or replaced. After that's sorted, clear the canons and go on a test drive to see if it resets. In case it resets, you'll have to continue your opinion. Depending on your vehicle you may have a vacuum operated selector or a vacuum solenoid if it's electrically actuated. In the case of the former, a hand held vacuum pump will have to be used to testit.The purpose is to see if the internal stopcock is getting turned by the selector, motor or solenoid. In order to do this, a command can be transferred to the system with scanner or by driving the vehicle under the special conditions that will spark the system. While this is passing keep an eye on the checkup tool data for the result.